Yamaha XMAX YP125R - Service manual > Starter clutch and generator (YP250R)

Removing the generator cover and stator coil

Removing the generator rotor and starter clutch

Removing the generator

1. Remove:

• Generator cover

TIP

Loosen each bolt 1/4 of a turn at a time, in stages and in a crisscross pattern. After all of the bolts are fully loosened, remove them.

2. Remove:

• Generator rotor nut "1"
• Washer

TIP

• While holding the generator rotor "2" with the sheave holder "3", loosen the generator rotor nut.
• Do not allow the sheave holder to touch the projection on the generator rotor.

Sheave holder 90890-01701

Primary clutch holder YS-01880-A

3. Remove:

• Generator rotor "1" (with the flywheel puller "2")
• Woodruff key

NOTICE

To protect the end of the crankshaft, place an appropriate sized socket between the flywheel puller set center bolt and the crankshaft.

TIP

Make sure the flywheel puller is centered over the generator rotor.

Flywheel puller 90890-01362

Heavy duty puller YU-33270-B

Removing the starter clutch

1. Remove:

• Starter clutch bolts "1"
• Starter clutch

TIP

• While holding the generator rotor "2" with the sheave holder "3", remove the starter clutch bolts.
• Do not allow the sheave holder to touch the projection on the generator rotor.

Sheave holder 90890-01701

Primary clutch holder YS-01880-A

Checking the starter clutch

1. Check:

• Starter clutch rollers "1"

Damage/wear → Replace.

2. Check:

• Starter clutch idle gear
• Starter clutch gear

Burrs/chips/roughness/wear → Replace the defective part(s).

3. Check:

• Starter clutch gear's contact surfaces Damage/pitting/wear → Replace the starter clutch gear.

4. Check:

• Starter clutch operation

a. Install the starter clutch gear "1" onto the starter clutch "2" and hold the starter clutch.

b. When turning the starter clutch gear clockwise "A", the starter clutch and the starter clutch gear should engage, otherwise the starter clutch is faulty and must be replaced.

c. When turning the starter clutch gear counterclockwise "B", it should turn freely, otherwise the starter clutch is faulty and must be replaced.

Installing the starter clutch

1. Install:

• Starter clutch
• Starter clutch bolts "1"

Starter clutch bolt 30 Nm (3.0 m*kgf, 22 ft*lbf) LOCTITE

TIP

• While holding the generator rotor "2" with the sheave holder "3", tighten the starter clutch bolts.
• Do not allow the sheave holder to touch the projection on the generator rotor.

Sheave holder 90890-01701

Primary clutch holder YS-01880-A

Installing the generator

1. Install:

• Starter clutch gear
• Woodruff key
• Generator rotor
• Washer
• Generator rotor nut

TIP

• Clean the tapered portion of the crankshaft and the generator rotor hub.
• When installing the generator rotor, make sure the woodruff key is properly seated in the keyway of the crankshaft.
• Make sure that the blunt-edged corner of the washer is facing outward.

2. Tighten:

• Generator rotor nut "1"

Generator rotor nut 80 Nm (8.0 m*kgf, 58 ft*lbf)

TIP

• While holding the generator rotor "2" with the sheave holder "3", tighten the generator rotor nut.
• Do not allow the sheave holder to touch the projection on the generator rotor.

Sheave holder 90890-01701

Primary clutch holder YS-01880-A

3. Apply:

• Sealant (onto the crankshaft position sensor/stator assembly lead grommet)

Yamaha bond No. 1215 90890-85505 (Three Bond No.1215)

4. Install:

• Oil seal "1"

Installed depth "a" 6.0-7.3 mm (0.24-0.29 in)

5. Install:

• Generator cover

Generator cover bolt 10 Nm (1.0 m*kgf, 7.2 ft*lbf)

TIP

Tighten the generator cover bolts in stages and in a crisscross pattern.

See also: