PIAGGIO Beverly 300ie - Service manual > Engine oil
Replacement
Change oil and replace filter as indicated in the scheduled maintenance table.
- In order to facilitate oil drainage, unscrew the cap/ dipstick "A".
- Unscrew the mesh pre-filter drainage plug "B" on the flywheel side and let the oil drain off.
- Once all the oil has drained through the drainage hole, unscrew and remove the oil cartridge filter "C ".
Make sure the pre-filter and drainage plug O-rings are in good conditions. Lubricate them and refit the mesh filter and the oil drainage plug, screwing them up to the prescribed torque.
Refit the new cartridge filter being careful to lubricate the O-ring before fitting it.
Add the recommended engine oil through plug "A". Then start up the vehicle, let it run for a few minutes and shut it off. After five minutes check the level and if necessary top up without exceeding the MAX level. The cartridge filter must be replaced every time the oil is changed.
N.B.
THE ENGINE MUST BE HOT WHEN THE OIL IS CHANGED.
Recommended products
eni i-Ride PG 5W-40 Synthetic based lubricant for high-performance four-stroke engines.
JASO MA, MA2 - API SL - ACEA A3
Characteristic
Engine oil
1.3 l
Check
This operation must be carried out with the engine cold and following the procedure below:
- Place the vehicle on its centre stand and on flat ground.
- Make sure the adjustment of the rear suspension is set to the minimum preloading position.
- Unscrew the cap/dipstick "A", dry it with a clean cloth and reinsert it, by screwing it in completely.
- Remove the cap/dipstick "A" again and check that the level is between the MAX and MIN marks. top-up, if required.
If the check is carried out after the vehicle has been used, and therefore with a hot engine, the level line will be lower; in order to carry out a correct check, wait at least 10 minutes after the engine has been stopped so as to get the correct level.
Oil top-up
The oil should be topped up after having checked the level and in any case by adding oil without exceeding the MAX level indicated on the cap/ dipstick. Restoring the level from MIN to MAX requires approximately 400 cm³ of oil.
Engine oil filter
Change oil and replace filter as indicated in the scheduled maintenance table. Use new oil of the recommended type for topping up and changing purposes.
Make sure the pre-filter and drainage plug O-rings are in good conditions. Lubricate them and refit the mesh filter and the oil drainage plug, screwing them up to the prescribed torque. Refit the new cartridge filter being careful to lubricate the O-ring before fitting it. Change the engine oil.
Recommended products
eni i-Ride PG 5W-40 Synthetic based lubricant for high-performance four-stroke engines.
JASO MA, MA2 - API SL - ACEA A3
Oil pressure warning light
The vehicle is equipped with a telltale light on the dashboard that lights up when the key is turned to the "ON" position. However, this light should switch off once the engine has started.
If the light turns on during braking, at idling speed or while turning a corner, it is necessary to check the oil level and the lubrication system.
See also:
PIAGGIO Beverly 300ie - Service manual > Maintenance, Maintenance chart
RESET SERVICE WARNING LIGHT At vehicle ignition, immediately after the ignition check, if there are less than 300 km (187.5 miles) to the next scheduled service, the corresponding icon flashes for 5 seconds. Once the service mileage has been reached, the icon remains steadily on until it is reset.
PIAGGIO Beverly 300ie - Service manual > Cooling system
Level check Check coolant when the engine is cold and as indicated in the scheduled maintenance tables, following the steps below. Set the vehicle upright on the stand and remove the cover by undoing screw "A". Remove the expansion tank cover "B" by turning it anticlockwise. Look inside the expansion tank and check that the level is between MIN and MAX. Top-up when the liquid does not reach the level MIN.
